Difference between revisions of "Logging Cable"
Jump to navigation
Jump to search
m |
|||
Line 1: | Line 1: | ||
− | There are a few cables that can be used to log and reflash data | + | There are a few cables that can be used to log and reflash data on Mitsubish ECUs: |
− | + | * OpenPort 1.0 (no longer available) | |
− | OpenPort 1. | + | * OpenPort 1.2 (no longer available) |
− | OpenPort 1. | + | * OpenPort 1.3M (no longer available) |
− | OpenPort 1. | + | * OpenPort 1.3D (available from [http://www.limitless.co.nz/cables www.limitless.co.nz/cables] |
+ | ** Datalogging only; no flashing support at all (needed physical wiring is not present). Low-cost logging option. | ||
− | OpenPort 1. | + | * OpenPort 1.3R (available from [http://www.limitless.co.nz/cables www.limitless.co.nz/cables] |
− | + | ** Physically identical to OpenPort 1.3U, but without a license for use with EcuFlash; only Evo 7/8 vehicles can be flashed with this cable, using EvoScan. Lower-cost than 1.3U. | |
− | |||
− | OpenPort 1. | + | * OpenPort 1.3U (only available from [http://www.limitless.co.nz/cables www.limitless.co.nz/cables]) |
− | + | ** Full-featured flashing/datalogging cable. Works with most loggers, as well as EcuFlash. | |
− | |||
− | |||
− | OpenPort | + | * OpenPort 2.0 (available from [http://www.limitless.co.nz/cables www.limitless.co.nz/cables] or [http://www.tactrix.com tactrix.com]) |
− | + | ** Newest version of full-featured cable; is now a device which supports CAN-bus vehicles such as the Evo X. Requires newer version of EcuFlash, and some loggers have not added support for it yet (EvoScan works). | |
− | |||
− | + | There have been quite a few additional cables produced over the years that EvoScan supports, but typically only Tactrix-licensed cables will operate with EcuFlash. | |
− | |||
− | |||
− | See [[ECU Development]] for schematics for the OpenPort 1.3U | + | See [[ECU Development]] for schematics for the OpenPort 1.0, 1.2, and 1.3U cables, as well as pinouts for the Evo ECUs, OBD-II, and diag plugs, and other useful electronics information. |
Latest revision as of 02:43, 4 May 2010
There are a few cables that can be used to log and reflash data on Mitsubish ECUs:
- OpenPort 1.0 (no longer available)
- OpenPort 1.2 (no longer available)
- OpenPort 1.3M (no longer available)
- OpenPort 1.3D (available from www.limitless.co.nz/cables
- Datalogging only; no flashing support at all (needed physical wiring is not present). Low-cost logging option.
- OpenPort 1.3R (available from www.limitless.co.nz/cables
- Physically identical to OpenPort 1.3U, but without a license for use with EcuFlash; only Evo 7/8 vehicles can be flashed with this cable, using EvoScan. Lower-cost than 1.3U.
- OpenPort 1.3U (only available from www.limitless.co.nz/cables)
- Full-featured flashing/datalogging cable. Works with most loggers, as well as EcuFlash.
- OpenPort 2.0 (available from www.limitless.co.nz/cables or tactrix.com)
- Newest version of full-featured cable; is now a device which supports CAN-bus vehicles such as the Evo X. Requires newer version of EcuFlash, and some loggers have not added support for it yet (EvoScan works).
There have been quite a few additional cables produced over the years that EvoScan supports, but typically only Tactrix-licensed cables will operate with EcuFlash.
See ECU Development for schematics for the OpenPort 1.0, 1.2, and 1.3U cables, as well as pinouts for the Evo ECUs, OBD-II, and diag plugs, and other useful electronics information.